Seatrium
Overview
Lead Process Engineer role at Seatrium. Responsibilities
Understand the Project & Client’s Contractual requirements and scope of work. Clarify scope of work and supply to form the contract basis with Client. Support Project Management Team on Process deliverable schedule updates. Preparation of Process Philosophies not limited to Control and shutdown philosophy, Preparation of Isolation philosophy, Sparing philosophy, P&ID philosophy, and Vent, Relief, and Flare load calculation philosophy Develop Process Simulation Heat and Mass Balances (H&M Sheets). Prepare Process Flow Diagram (PFD), Utility Flow Diagram (UFD) and Piping & Instrumentation Diagram (P&ID), Cause and Effect Diagrams and Safe chart Perform Equipment Sizing Calculations (Separators, Vessels, Storage tanks etc.), Line Sizing Calculations and Hydraulic Analysis and Flare Network design Prepare and review technical queries and assist Lead Engineer in concluding TQs with Client. Conduct Process studies like Dynamic Depressurization study. Prepare reports, including Process System design report, vent and drain report, Utility summary. Prepare Process datasheets for Mechanical Equipment and Instruments. Coordinate with other disciplinary departments for process inputs. Provide input for Interdisciplinary checks and contribute to deliverables such as MEL, Electrical Load List, Topsides Weight report, mechanical and instrument datasheets, and other discipline critical philosophies, as required. Review Vendor documents and provide comments to ensure vendor design aligns with project requirements. Update Third Party Specialist, Process & Safety studies, including follow-through of all such studies (review study reports, attending workshops, etc.). Assist Lead Engineer in managing interface with hull and marine systems (e.g., Cargo, Utilities). Provide input to Operating manual, Pre-commissioning and commissioning manual. Attend project meetings as required (intra-discipline; Client, inter-discipline, SCM and Sub-contractor / vendor / 3rd Party) and follow through with meeting actions. Identify and address Client comments/requirements; provide feedback to Project Management and Commercial team; raise trends or potential change orders as necessary. Assist Lead Engineer for project process engineering support through after Engineering kick start, Detail Engineering / As-Built Engineering / Pre-Commissioning and Commissioning / Warranty Test Run, as required. Support process design data collection, analysis, and maintenance for feasibility studies, tender/construction documents, and basic and detailed design drawings. Assemble process design submittal manuals/booklets including drawings, schematics, documents, reports, calculations, etc., and provide copying support for contractors/customers. Liaise with package engineer to obtain updated information and maintain process design submittal filing in the engineering reference library. Prepare process design project training manuals and owner’s manuals for on-site training to contractors and customers. Monitor and follow up changes updated by junior team members on the operational process project drawings and records, including lessons learned from project execution. Job Requirements
Four-year bachelor’s degree in chemical engineering or related engineering disciplines 10 years of design work experience in Offshore industry Proficient with MS Project, Excel, Power Point and Outlook Impeccable communication skills both written and verbally Preferred Skills
Effective analytical, problem-solving and organizational skills Effective organization skills including the ability to prioritize and plan work Oriented with the ability to multi-task Employer
Seatrium Limited
#J-18808-Ljbffr
Lead Process Engineer role at Seatrium. Responsibilities
Understand the Project & Client’s Contractual requirements and scope of work. Clarify scope of work and supply to form the contract basis with Client. Support Project Management Team on Process deliverable schedule updates. Preparation of Process Philosophies not limited to Control and shutdown philosophy, Preparation of Isolation philosophy, Sparing philosophy, P&ID philosophy, and Vent, Relief, and Flare load calculation philosophy Develop Process Simulation Heat and Mass Balances (H&M Sheets). Prepare Process Flow Diagram (PFD), Utility Flow Diagram (UFD) and Piping & Instrumentation Diagram (P&ID), Cause and Effect Diagrams and Safe chart Perform Equipment Sizing Calculations (Separators, Vessels, Storage tanks etc.), Line Sizing Calculations and Hydraulic Analysis and Flare Network design Prepare and review technical queries and assist Lead Engineer in concluding TQs with Client. Conduct Process studies like Dynamic Depressurization study. Prepare reports, including Process System design report, vent and drain report, Utility summary. Prepare Process datasheets for Mechanical Equipment and Instruments. Coordinate with other disciplinary departments for process inputs. Provide input for Interdisciplinary checks and contribute to deliverables such as MEL, Electrical Load List, Topsides Weight report, mechanical and instrument datasheets, and other discipline critical philosophies, as required. Review Vendor documents and provide comments to ensure vendor design aligns with project requirements. Update Third Party Specialist, Process & Safety studies, including follow-through of all such studies (review study reports, attending workshops, etc.). Assist Lead Engineer in managing interface with hull and marine systems (e.g., Cargo, Utilities). Provide input to Operating manual, Pre-commissioning and commissioning manual. Attend project meetings as required (intra-discipline; Client, inter-discipline, SCM and Sub-contractor / vendor / 3rd Party) and follow through with meeting actions. Identify and address Client comments/requirements; provide feedback to Project Management and Commercial team; raise trends or potential change orders as necessary. Assist Lead Engineer for project process engineering support through after Engineering kick start, Detail Engineering / As-Built Engineering / Pre-Commissioning and Commissioning / Warranty Test Run, as required. Support process design data collection, analysis, and maintenance for feasibility studies, tender/construction documents, and basic and detailed design drawings. Assemble process design submittal manuals/booklets including drawings, schematics, documents, reports, calculations, etc., and provide copying support for contractors/customers. Liaise with package engineer to obtain updated information and maintain process design submittal filing in the engineering reference library. Prepare process design project training manuals and owner’s manuals for on-site training to contractors and customers. Monitor and follow up changes updated by junior team members on the operational process project drawings and records, including lessons learned from project execution. Job Requirements
Four-year bachelor’s degree in chemical engineering or related engineering disciplines 10 years of design work experience in Offshore industry Proficient with MS Project, Excel, Power Point and Outlook Impeccable communication skills both written and verbally Preferred Skills
Effective analytical, problem-solving and organizational skills Effective organization skills including the ability to prioritize and plan work Oriented with the ability to multi-task Employer
Seatrium Limited
#J-18808-Ljbffr